Faucet & Valve Repair in Union City, GA

When a kitchen faucet is past repair, the replacement has to fit a sink, counter and cabinet that are staying put. Most of the trouble after a faucet swap comes from measurements nobody took: a lever that bangs the backsplash, a spout that aims at the divider between bowls, or a pull-down hose with nowhere to hang. Faucet repair visits in Union City sometimes end with the homeowner choosing a new faucet, and a few minutes with a tape measure makes that choice much easier.

Count the holes

Look under the sink or lift the current faucet's base plate to see how many holes the sink or counter has. Many kitchens have one to four: a faucet, a side sprayer, a soap dispenser or a filter tap. A single-hole faucet can cover a three-hole sink with a deck plate, and extra holes can take a soap dispenser or cover cap. Going the other way, from one hole to a faucet that needs three, means drilling the counter or sink, which is not always possible with stone or enameled cast iron.

Reach, height and swing

• Spout reach: measure from the faucet hole to the center of the main bowl. A spout that falls well short splashes against the back of the sink.
• Spout height: tall pots fit better under a high arc, but check the clearance under any window sill, shelf or cabinet above the sink.
• Handle swing: side levers need room to rotate fully, and a rear-swinging lever needs space before the backsplash or window.
• Double bowls: the spout should swivel far enough to reach both bowls without hitting anything.

Under the sink

A pull-down or pull-out faucet hangs a hose and weight in the cabinet, and that loop needs space clear of the disposal, a filter system and the drain trap. A crowded cabinet can keep the head from retracting. Check the supply connections too: most new faucets come with flexible lines sized for standard stop valves, but older stops may have different outlets or be worn enough that replacing them during the swap is sensible. On a thin stainless sink, a faucet with a heavy base may need a reinforcing plate underneath so the mounting holds firm.

Valve type and parts support

Most new kitchen faucets use a ceramic disc cartridge, which tends to hold up well and can be replaced when it eventually wears. Choosing a brand with readily available cartridges and spray heads, and keeping the model number with the paperwork, makes future faucet repair easier. Read the manufacturer's warranty terms, which often cover parts for a set period and may require registration. Finish matters for appearance and cleaning, but the internal valve and parts availability matter more over the long run.

What changes with the faucet

The disposal, dishwasher connection and filter often share the cabinet with the new faucet. If the disposal is leaking or near the end of its life, it can be swapped through garbage disposal repair in Union City while the cabinet is empty. If the old faucet failed early and other fixtures are dripping too, a water pressure check can rule out pressure that is wearing parts out. Installing the new faucet, and replacing tired stops at the same time, is part of Alpha's faucet and valve repair and replacement service.

Remodels and the Union City permit office

Union City's Building Permits Division says most projects need a permit, and a kitchen remodel that moves the sink is the kind of project to raise with the division before work starts.

Questions about choosing a kitchen faucet in Union City

Can I put a single-handle faucet on a sink with three holes?

Usually. Many single-handle kitchen faucets ship with a deck plate for exactly that, and the spare holes can take a soap dispenser, a filter tap or a side sprayer instead. The plate has to match the hole spacing and sit flat on the curve of the sink, so check its size before buying.

How do I know if a pull-down faucet will fit my cabinet?

Picture the hose hanging in a loop below the sink and being pulled up again: it needs a clear path past the disposal, the trap and any filter housing, and room for the weight to slide. A cabinet that is already crowded is often better served by a pull-out model with a shorter hose, or by a separate side sprayer.

Can I install the new faucet myself?

Many homeowners do, especially when the hole layout matches and the stops under the sink close properly. The usual snags are corroded mounting nuts on the old faucet, a stop that will not shut off and a disposal or filter that leaves little room to work. If any of those apply, having the swap done avoids a cabinet full of water.

Choose with confidence

Narrowing down a replacement kitchen faucet for your Union City home? Alpha Plumbing and Sewer can check the measurements, the stops and the cabinet before you buy. Call (404) 409-4448.